Kenneth Alrick is senior welding product manager, ESAB Welding and Cutting Products.Click image to enlargeby Kenneth Alrick

Advanced controls improve AC GTAW aluminum results

If you own a smart phone, chances are you take advantage of its applications and functions to make your life easier–has anyone looked at a paper road map lately? The same holds true for inverter-based GTAW power sources with advanced controls for adjusting the AC output to optimize results for specific applications. Here is a quick overview to get you started.

Balance control: This function adjusts the amount of time the waveform spends in the electrode negative phase (EN, which does the welding work) and the electrode positive phase (EP, which provides the cleaning action necessary to remove surface oxides). With inverters, you can set the balance control from 10 to 90 per cent EN. In many applications, you can set EN at 70 per cent or above, which will allow you to remove heat from the electrode and help maintain a pointed tungsten (more on pointed electrodes below).

Frequency adjustment: With an inverter, you can adjust the welding output frequency, such as from 20 to 200 Hz. Increasing frequency concentrates the arc column and prevents the arc from wandering. As a result, you can increase travel speed, narrow the oxide etch zone and put in a narrower weld bead. To start, experiment with frequencies from 100 to 150 Hz, especially if you want to prevent overheating thin sections and over-welding on fillet welds.

Pulsed AC TIG: A lot of welders confuse AC frequency adjust (the rate at which the current changes from positive to negative) with pulsed welding, which pulses the welding output from a high peak output to a low background output. Pulsing further lowers heat input, which prevents burn-through on thinner materials. It also affects the weld bead profile, specifically the distance between the “stacks of dimes.”

Some power sources enable pulsing the AC or DC output from 0.2 to 2000 Hz. Background current can be adjusted from 1 to 200 per cent of welding current, and the duration of the background pulse can be adjusted from 1 to 99 per cent of total cycle time. As a starting point for aluminum, try setting background current and pulse duration at 50 per cent and experiment from there. Most operators end up with values between 30 and 50 per cent for both parameters. As for pulse frequency for manual welding, start at 1.0 Hz and adjust as desired.

Save your parameters: After dialing in balance control, frequency and pulsing parameters, use the machine’s ability to store parameters for quick recall the next time you encounter the same application.

Tungsten selection: For welding with an inverter, use a ceriated (orange band) or lanthanated (blue band) electrode. The addition of 1.5 to 2.0 per cent of these rare earth elements enables the electrode to maintain a point instead of ball up like a pure (green band) tungsten will. As an added benefit, using these electrodes lets you switch between the AC and DC welding processes without changing electrodes. Because electricity likes to come off a point, using a pointed tungsten promotes a narrow arc cone and more precise welding. Historically, operators chose a 2 per cent thoriated tungsten (red band) when they wanted to weld with a point. However, thorium is a radioactive element; due to safety concerns, this type of tungsten is no longer the best choice.

Tungsten preparation: Prepare the electrode with a tungsten grinder or grinding wheel dedicated to the task to prevent contamination. Grind with the grain (longitudinally) to create a taper that is about two or two-and-a-half times the diameter of the electrode. For welding at 40 amps or below, use a sharp point. For welding at higher amperages, put a small flat on the end of the tungsten to prevent the tip from breaking off and becoming included in the weld bead.

With so many variables to AC GTAW variables to adjust, you’ll want to practice on scrap aluminum before welding on actual parts. However, with just a little added effort, you’ll greatly increase your ability to control the arc, tailor the welding output to match the application at hand and improve productivity and quality. SMT

Kenneth Alrick is senior welding product manager, ESAB Welding and Cutting Products.


Inverter-based technology for TIG welding

Aspect 375 is an inverted TIG welding system that offers welders a more efficient welding process.

Welding tech tips: fume extraction

by Etienne Blouin & Jim Dileo

Fume extraction welding guns remove harmful welding fumes efficiently

Multifunction five-axis machining centre

Makino's iGrinder five-axis horizontal machining centre combines grinding, milling, drilling, and tapping, all on the same platform. Watch it in action.

Chip formation in indexable drilling

Effective chip control is the most important factor in indexable insert drilling operations and is essential for quality hole making.

Welders among high paying jobs that don't need a degree

Welders, pipe fitters and electricians are cited in a Workopolis survey among the high paying jobs in Canada that don't require a university degree.

Will reshoring offshore again?

India has a problem and it's looking at manufacturing to fix it. The country's services sector, which has driven economic growth in that country for years, is shrinking and some are proposing India refocus its efforts on manufacturing

The Internet of Things on the shop floor: White Paper

Walter Surface Technologies has published a white paper on how the Internet of Things is impacting the metalworking shop floor.

Multi-purpose welding in heavy equipment environments

The Flextec 650 multi-process welder from Lincoln Electric delivers up to 650 amps of welding power. 

The sky's the limit

Finding opportunity in Canada’s aerospace industry

by Tim Wilson

As Canadian job shops read the sobering tea leaves on the ups and downs of the manufacturing sector, here are some stats that might make them tipsy: in the next twenty years the big aircraft manufacturers are expecting $4 trillion in global orders from 34,000 new aircraft.

Getting the order

by Tim Wilson

The dark art of job estimating brought to light

Ask someone how he estimates a job and you’ll likely get a wry smile, perhaps a wink.

Physics busters

These ten objects seem to defy the laws of physics.

Laser/punch combination meets productivity challenge

See how a new Prima Power LPe6f laser/punch combination, integrated into the Night Train (NT) Material Management System, helped Accelerated Cooking Products (ACP) of Cedar Rapids, IA, achieve a dramatic increase in productivity at a time when new business increased threefold.

Italy's top metal fabricating show: Lamiera 2019 in Milan

If you operate a metal fabricating business in Canada, the Italian Trade Commission wants to hear from you. It is inviting candidates to contact the office for a trip to Milan, Italy to attend the country's largest metal fabricating trade show, Lamiera 2019.

A Few Words to Describe 2020


During the past eight months I have heard this year described in a vast number of ways. I won’t list them, but a lot of them were fearful, most of them were cautious, many of them colourful and almost all of them decidedly negative. 

FABTECH 2014: Welding fume extraction system

Exhibitor: Miller Electric    Booth: C2944

Stay In Touch

twitter facebook linkedIn