Click image to enlarge

by Keith Werkley, regional sales manager, Weldcraft

 Just like any part of the TIG welding process, learning how to assemble and install your TIG torch properly may seem intimidating at first.

The torches feature multiple interchangeable parts that must be properly assembled to achieve good welding performance. Plus, both air- and water-cooled models have specific requirements for installation. Nonetheless, educating yourself as to the proper procedures for both types of TIG torches can go a long way in preventing problems and ensuring quality welds.

The torch and its components

To aid in joint accessibility and increase operator comfort, TIG torches are designed in a variety of shapes and sizes. Typically, air-cooled torch are larger and heavier than water-cooled torches. The cooling capacity required for a particular application, as well as the location where you are welding dictates which one you should use.

For example, if you have a low-amperage application, it is best to use an air-cooled TIG torch. These torches also work well outside because they do not require a separate water cooler and are easily portable. Water-cooled torches are recommended for applications requiring more than 200 amps and are good for use in the shop.

Before assembling your TIG torch, first consider each of its components. If you have an air-cooled torch, some components may be larger than those built for water-cooled torches. These larger components are necessary due to how these torches dissipate heat. Air-cooled torches rely on ambient air plus Argon gas to cool the torch and need the additional surface area of the components to assist in the process. On the other hand, a water-cooled torch has a constant source of coolant removing the heat and therefore has smaller front-end torch parts.

In a TIG torch, the nozzle (also called a cup) directs shielding gas to the weld puddle, while also protecting it and the electrode from outside contaminants. Nozzles range in size from ¼-in. (#4) to 1-in. (#16) and are made primarily of alumina or lava.          

The tungsten electrode conducts heat to the arc. The thickness and type of material you are welding, along with whether you weld with alternating or direct current determine which type of tungsten you should use. A 3/32 in. two per cent ceriated tungsten electrode is a common choice, as it can be used for welding at 10 to 250-amps. Other tungsten electrode options include pure tungsten, two-percent thoriated, 1.5 per cent lanthanated, zirconiated and rare earth.

The size of tungsten you use will determine what size collet and collet body you need (e.g. a 3/32 in. collet matches 3/32 in. tungsten). The collet and collet body are responsible for holding the tungsten electrode in place. If you require greater joint access or better shielding gas coverage, you can replace a collet body with a gas lens. Gas lenses are recommended for welding on highly reactive alloys as the greater gas coverage can prevent contamination. All air- and water-cooled GTAW torches are compatible with gas lenses. Your amperage requirements, tungsten size and joint configuration will determine the gas lens and corresponding nozzle size you need.

To complete the back end of your TIG torch, you will need to decide between a short, medium or long back cap, all of which tighten the collet against the collet body to help hold the tungsten in place.  The length you choose depends on the joint access you require on your application.

Finally, consider your available hose and power cables: rubber or vinyl.  Vinyl works well for light-duty applications; however, braided rubber hoses resist heat and kinking and tend to last longer.  Rubber hoses also maintain flexibility and durability in cold environments better than vinyland are typically standard on air-cooled TIG torches.

Assembling

Once you’ve identified the torch components you need, you’re ready to assemble your TIG torch. The steps are the same whether you have an air- or water-cooled model.

 First assemble the collet and collet body. Then insert the tungsten electrode, making sure you have a tight fit between the collet and electrode. Doing so helps ensure good conductivity and a stable arc.

Next, insert the back cap into the torch body (but do not tighten it) and insert the tungsten/collet/collet body assembly. Add the nozzle and adjust the electrode to within ¼ in. beyond the end of the nozzle. Hand tighten the back cap. Tightening the back cap at this stage ensures a secure fit of the tungsten and the collet within the collet body.

If you choose to replace the collet body with a gas lens, you can extend the tungsten electrode further  (up to ½ in. beyond the nozzle) but you will also need to use a larger nozzle. Your local welding distributor or TIG torch manufacturer can help you determine the correct size to use.

Lastly, be certain that all of the torch component threads and connections are tightened properly. Tight connections prevent problems with electrical conductivity and gas flow that could lead to torch damage or weld discontinuities. Also check all o-rings and gaskets for deterioration or failures that could allow air to be drawn into the shielding gas stream.

Powering Up

Before installing your TIG torch, be certain to turn off your power source.

To install an air-cooled torch, first select the appropriate power cable adapter for your TIG power source and connect it to the torch’s power cable. Consult with your welding distributor for the correct one for your particular power source. Connect the power cable adapter to the electrode terminal of the power source, making certain the connection is snug. Tight connections prevent overheating and damage to the torch cable.

Next, connect the gas hose to the gas-out connection on the power source and attach a flowmeter regulator to the cylinder; the flowmeter regulator precisely controls the shielding gas flow.  Connect the gas hose from the flowmeter regulator to the gas-in connection on the back of the machine, tighten it and open the gas cylinder valve. Remember, tight connections eliminate shielding gas loss and allow steady flow of the shielding gas to the torch, which in turn promotes good weld quality. 

The next step is to connect either the foot pedal or fingertip remote control. The remote control should connect to the remote receptacle on the front of your power source. Using a foot pedal control works well for welding at a bench, while a TIG torch with a fingertip remote control offers greater mobility and eases welding in tight spaces or awkward positions.

You’re now ready to weld - attach your work clamp from the work output terminal of the machine to the work piece and prepare to strike your arc.

Installing a water-cooled TIG torch is similar to installing an air-cooled torch with the addition of a few steps. First, check that the required water-cooler has enough coolant, usually about three gallons. Use only distilled water or an approved welding coolant available through your distributor or contact the manufacturer of the equipment for information. Never use city water, anti-freeze and/or any other rust-inhibiting compounds.

Click image to enlarge

This diagram shows the proper connection of a water-cooled GTAW torch from the water cooler to the power source.

 

When connecting the water-cooled TIG torch to the water-cooling system it is important to set up the water flow properly (See figure 1 for a diagram). First, connect the torch’s output water hose (smaller left-hand fitting – blue hose) to the water-out connection on the cooler. Then connect the coolant return/power cable (larger left-handed fitting – red hose) to the power cable adapter and connect that adapter to the output terminal. Next, plug the water cooler into the welding machine receptacle.

As with air-cooled torches, connect the gas hose from the flowmeter regulator to the gas-in receptacle on the back of the machine and connect the gas hose to the gas receptacle on the machine. Connect the foot pedal or remote fingertip control.      

Once all of the connections have been made, attach the work clamp to your work piece and turn on the power source. You’re now ready to weld with a water-cooled torch.

Start Welding

Following the proper procedure for assembling and installing your TIG torch is the first step in ensuring your welding success. Still, don’t forget to practice and test your system to find what works best for you. Also, remember you can consult with your local welding distributor to discuss other best practices that may help improve your TIG weld quality and your skills.

Weldcraft

 

New welding and consumables catalogue

Bernard and Tregaskiss have released a joint MIG welding guns and consumables catalogue.

Welding camp for students in Newfoundland and Labrador

The CWA Foundation has introduced students in Newfoundland and Labrador to the welding profession by funding a Mind Over Metal welding camp in the province.

Feds invest $49 billion for aerospace innovation

The Federal Government of Canada is investing $49 billion in aerospace innovation to support competitiveness in the sector.

Energizing a business

by Tim Wilson

The Problem: Build long term capabilities to serve Alberta's energy sector

The Solution: Cross-train a skilled workforce on advanced machinery

Alberta manufacturer looks to position itself for the future

Robotic education cell for training

Lincoln Electric partnered with Fanuc to create the robotic education cell. It serves as a portable training system for classroom use and gives students the opportunity to gain insights into proper programming for operating a robot.

Welding education conference focus

More than 50 educators from across Canada participated in the Canadian Welding Association's (CWA) annual Welding Educators Conference earlier this year at Nova Scotia Community College's Akerly Campus in Dartmouth, NS.

Bright future for welders: news story

A Southwestern Ontario newspaper has published a news story highlighting careers in welding for youth. 

Welding for motorsports: Lincoln seminar

Lincoln Electric hosted metal fabricators in the racing industry during its Advanced Motorsports Welding seminar held at its Cleveland, OH, world headquarters.

2018 SHOP TALK

by Andrew Brooks

Job shops in Canada discuss challenges and successes

Job Shops | Ontario: Investing In Growth

Article by Peter Diekmeyer

Photos by David Afriat

Translas partners with Gullco on distribution deal

Translas, a global manufacturer of on- torch fume extraction solutions, has announced a distribution partnership with Gullco International Ltd. Based in Newmarket, Ont., Gullco will be the global distributor of Translas’ newest fume extraction solutions, namely Translas 7XE Semi-Automatic Fume Extraction welding gun and the ClearO2 W-Series hi-vac units, designed and engineered for welding automation.

The lighter side of welding

by Tim Wilson

Lightweight alloys present new welding challenges

Irving Oil $200 M project a boon to Atlantic Canada

Irving Oil has announced plans to invest $200 million in a turnaround project at its Sain John, NB, facility that is expected to generate approximately 3,000 jobs for onsite workers.

1,800+ attend first Montreal CanWeld event

More than 1,800 people attended CanWeld 2017 in Montreal, QC. Held at Place Bonaventure September 12 and 13, the event included the welding industry's well-known CanWeld conference with 346 attendees and a trade show featuring close to 50 exhibiting companies.

Portable wire feeder with less actual wires

Lincoln Electric’s LN-25X portable industrial wire feeder is equipped with the company’s CrossLinc and True Voltage Technology (TVT).

Stay In Touch

twitter facebook linkedIn