Dan Cormier is an application specialist with Dormer Pramet.Click image to enlargeby Dan Cormier

What you need to know when drilling, milling, turning or tapping

Stainless steel’s anti-corrosive qualities makes it perfect for use in a huge range of environments and components such as aerospace, general engineering, consumer, oil and gas, medical and marine industries. Its versatility is reflected by the fact that there are more than 150 different grades. The main alloying element is Chromium. As a general rule, resistance to corrosion and oxidation increases with Chromium content. Other alloying elements such as Nickel and Molybdenum can be added to change the structure, increase corrosion resistance and improve strength.

Due to the difficult process of machining stainless steel, manufacturers have developed new ways to combat application challenges: changes to the cutting tool design, new geometries, improved coolant and stronger coatings to improve performance and tool life. For example, drills with thin margins reduce contact with the hole surface, which in turn minimizes friction between the cylindrical land and the hole walls and decreases work hardening and temperatures. Positive point geometries ensure excellent chip breaking, while a specially designed web combines the benefits of maximum rigidity with space for efficient chip removal.

Here are five key factors to consider.

1. Coolant
A generous flow of cutting fluid removes heat from the chip, helps chip breaking and improves dimensional stability of the component. Cutting tools with through coolant provide instant cooling at the cutting interface, which helps chip breaking and evacuation. When using flood coolant, ensure a plentiful supply, as coolant starvation can cause temperature fluctuations and thermal cracking, resulting in reduced tool life. Neat cutting oils work well but, if using an emulsion, an eight to ten per cent concentration is recommended.

Chipbreaker in  action during turning. Click image to enlarge2. Feed Rates
Stainless steels can vary slightly between different suppliers and batches. When choosing cutting data it’s a good idea to begin at the lower region of the manufacturer’s recommendations. High feed rates can cause heat transfer in the cutting tool, increasing tool wear.

3. Work Hardening
Some stainless steels are prone to work hardening during machining. This can have a negative effect on tool life and also reduce the life of subsequent tools used. To minimize this, avoid using tools with worn edges, which could accelerate tool wear and cause breakage. Make regular checks for signs of wear and change tools or inserts regularly. Also, try to avoid any dwells or pauses in the cutting process as this will cause heat build-up and increase work hardening.

Cutting stainless steel.Click image to enlarge4. Mechanical Properties
The high strength of stainless steels combined with their high ductility makes chip breaking more difficult. This increases the risk of vibration, which can affect surface finish quality and reduce the service life of the tool or insert. To address this, make sure tooling and workpieces are stable and well clamped. Keep tool overhang to a minimum, especially when drilling or internal turning. To help reduce vibration, use sharp tools or inserts with a small nose or corner radius.

5. Threading
When tapping stainless steels, tool life can be increased by pre-drilling the hole 0.1 mm larger than recommended. This will reduce torque levels encountered during threading which, in turn, increases tool life and performance. SMT

Dan Cormier is an application specialist with Dormer Pramet.

 

 

Precise Priorities

by Noelle Stapinsky

Growing with its customers is Brematech’s main focus

Makino’s next generation vertical machining centres

Building on its PS-Series product line, Makino has introduced the next generation PS65 and PS105 vertical machining centres. Watch them in action here.

Selecting a Positioner

by Cliff White

Factors to consider to ensure you have the right one for your shop

Horrendous Holes

by Kip Hanson

Cutting super alloys can be a formidable machining challenge

Nickel and cobalt-based superalloys may not be Kryptonite, but drilling holes in Hastelloy X, Inconel 625, Waspaloy and Haynes 25 is about as tough as it gets in the world of metal removal. With machinability ratings in the low teens, these nightmare materials test the patience of even the most cool-headed machinist.

Robots producing robots

KUKA robots producing robots together with workers.

Digital directions

by Mary Scianna

As cutting tool data management moves further into the digital world, what does it mean for
your machining operations?

CMTS Highlights: Sandvik Coromant "Smart Hub"

In the competitive cutting tool industry, suppliers need to set themselves apart from the competition.

Improve chip control in turning operations

Sandvik Coromant presents some tips to improve chip control and reduce chip jamming in turning operations.

Getting a better grip on toolholding systems

Like many shops, Applied Engineering Inc., spends quite a bit of money on tools each year. So it was pleasantly surprised when a new toolholding system from Haimer began doubling tool life and cutting overall costs.

Identify theft

In the movie “Identity Thief” actor Jason Bateman plays the role of a man whose identity is stolen by a con artist. 

The additive way

A Q&A with Renishaw Canada’s Mark Kirby about the current state of additive manufacturing

The macro on micro holes

Micro holemaking presents unique challenges

by Ed Robertson

Production efficiencies dictate doing more with less. Fixtures and workholding systems can accommodate families of parts; tools and inserts can accomplish numerous functions such as milling, turning, and holemaking; and multi-tasking machining centres with various spindles, axes of motion, rotating worktables and the like, all offer the promise of greatly improving production efficiencies and lowering throughput times and costs.

The problem with the skilled trades shortage: Us

The government has announced it’s revamping its immigration rules to increase the speed of skilled trades immigrants into Canada.

It's time to "take back manufacturing"

Initiative looks to reverse manufacturing industry’s declining trend

by Nigel Southway

It’s now clear to many Canadians that it’s time to rescue our declining manufacturing industries. 
Planning for the future

by Tim Wilson

An exit strategy for all seasons

Stay In Touch

twitter facebook linkedIn