Cutting Tools Tech Tips: Centering your machining centre processesClick image to enlarge

By Tim Fara, Bilz Tool Co.

Machining centre manufacturers spend effort, design, and cost to make sure the spindle in the machine will operate on centreline. Spindle rotational accuracy as well as spindle alignment play an important role in cutting tool performance and productivity.

Cutting tool manufacturers use the latest materials and grinding equipment to assure the cutting edges are uniform in location, size, and tolerance to the centreline. This assures the tool will rotate on the centreline.

With these issues getting so much attention and focus, why do we pay so little attention to the accuracy of our toolholder and tool clamping products and the maintenance of the spindle rotational accuracy? The tool “connection” between the machine tool spindle and the cutting tool is as important as the maintenance of the jet engine. If airlines did not maintain the engines regularly, flying would be a lot more dangerous and expensive.

Studies have shown that for every .0001 in. the cutting edge runs out on TIR, the cutting tool edge life is reduced by an average of 10 per cent. This means a $100 cutting tool operates as a $90 one with just .0001 TIR and as a $50 tool with a .0005 TIR.

So how do you maintain the centreline of your manufacturing processes?

1) Spindle Taper maintenance and care. On a daily basis, use a spindle wiper to ensure your spindle taper is free from fine metals caused in the machining process and passed through the coolant onto the toolholder and machine spindle during tool changes. The fines can embed in the spindle taper as well as the coolant and tram oil can be “squeezed” into a thin sticky layer holding the fine metal particles. This causes excessive toolholder shank wear and potentially excessive spindle taper wear leading to excessive TIR in the connection.

2) Spindle alignment. Since all spindles rotate and most are on a rotational axis, alignment in reference to the centreline of rotation is critical to cutting tool location “away” from the spindle face. Axial runout and the spindle rotational axis in reference to your table/fixture, determines the runout of your cutting tool edge and this determines your cutting edge tool life even before you start machining. Spindle alignment test arbors used in your PM (preventative maintenance) program will make sure your spindle alignment, as well as your spindle rotational accuracy is maintained. Test arbors will even help indicate when your spindle bearings are showing excessive wear and run-out.

3) The spindle drawbar. Maintaining this within factory specifications is critical to the life of spindle bearings, spindle taper surface, and toolholder taper accuracy. If a drawbar fails to maintain the proper load on the connection, metal removal rates are reduced due to chatter, cutting tool movement, and cutting tool edge location based on programming location. In addition, vibration between the “loose connection” and the taper interface will cause excessive spindle taper wear, fretting (a burning of the material surface due to high frequency vibration between surfaces) – which damages spindle and tool taper material integrity. Pull force gauges should be part of your regular PM program to ensure that the machine manufacturer’s drawbar tension force is maintained.

Toolholder selection is important. Poor quality (low TIR accuracy tool holders) can push your spindle rotation TIR to .0005 -.0009 or higher, costing you valuable tool edge life and production rates. With the evolution of the tool holders from end mill holders through collet chucks to today’s shrink fit technology; the TIR has improved with every evolution/innovation of the tool holders in the market.

Maintenance of the tool holder system is critical to the accuracy of the assembly as well. What impacts the maintenance of a tool holder?

1) Proper torquing of the collet nut to proper grip the cutting tool shank in the collet. Under torquing the collet nut will allow the collet to grip the cutting tool shank with less strength and machining dynamics will cause the cutting tool to move in the assembly. Over torquing the collet nut will cause the collet to “twist” thus causing axial run-out in the tool assembly and collet fatigue reducing the clamping strength of the collet over time.

2) Proper cleanliness when assembling the tool clamping system – removal of all chips and grime from tool taper and ID taper before assembly

3) Retention stud installation is important because improper torquing of the retention stud will cause distortion of the tool taper leading to taper contact reduction and axial run-out growth.

4) Handling of the tools from storage to machine carousel determine how well the tool taper is maintained. Improper handling of the tools allows the tapers to get knicked, dented, or scratched, which destroys the taper surface.

Two important facts to consider:

Average tool holder shank accuracy is three to five years before the taper is beyond standard manufacturing tolerances from wear and every day use. This means that the taper will have excessive TIR in it resulting in loss connection TIR.

Putting “used” toolholders on new machine spindles reduces the life of the new machine spindle taper surface by 50 per cent because you introduce “poor” quality connections to a new connection accelerating the wear on the new machine spindle surface.

You can get a lot more out of your machine and machining processes if you are centered with your machining centre processes. This is where quality and price determine the outcome of machining performance and machining costs.

Timothy Fara is managing director of Bilz Tool Co. Inc.

Creating Value

by Michael Ouellette

I have been covering Canada’s manufacturing sector for a long time—about 20 years—and have been witness to an incredible amount of change in that time.

Shop thought - Educate your workers

To learn about new manufacturing technologies and educate your shop floor workers, does your company prefer to use online resources such as webinars, or does it send people off site to trade shows, conferences and seminars?

Turn Right

by Kip Hanson

Breaking with tradition in turning operations can bring big benefits 

Gas Management For Industry 4.0

by Professor Emil Schubert

Rapid liquid printing

If you thought 3D printing was leading edge, wait until you see 4D printing, being developed at MIT’s Self-Assembly Lab.

Electric pipe bending machine boosts fabricating efficiency

A large bore hydrualic part maker has improved production efficiency and accuracy using an all electric pipe bending machine

Frank Mohn Piping in Frekhaug, Norway, installed the custom pipe bender from Unison to help improve fabricating through-put and accuracy. According to Unison, the all electric machine is the most powerful pipe bender it has delivered to a custoemr to date. 

DMG MORI open house: machining innovation in action

A novel approach to additive manufacturing, an iPad for machine tools and 66 different machine tool demonstrations were part of the draw of a DMG MORI open house in Pfronten, Germany, for more than 6,000 manufacturers from around the world, among them more than 40 Canadians.

Beating back competitive pressures in the auto sector

by Tim Wilson

Competitive pressures in the automotive sector

Keeping the doctor away

Creating a health and safety program that fits your shop’s needs

WATCH: Micro machining of a watch

Watch how Horn tooling micro machines a watch.

Efficient tool setup

by John Ripka

If your punch press is not punching parts 100% of the time, it’s not making money

Medical Manufacturing: A leg up

by Tim wilson

Prescriptions for success in medical manufacturing

The power of one

by Tim Wilson

The Problem: Build footprint to capture bigger deals in injection mould market

The Solution: Merge two competitors to go after niche global opportunities

Ontario injection mould businesses merge to create stronger company

Stay In Touch

twitter facebook linkedIn