CANADA'S LEADING INFORMATION SOURCE FOR THE METALWORKING INDUSTRY

LATEST MAGAZINE

CANADA'S LEADING INFORMATION SOURCE FOR THE METALWORKING INDUSTRY

CANADA'S LEADING INFORMATION SOURCE FOR THE METALWORKING INDUSTRY

Drilling deep

Share This Post

by Luck Pollock

Solid carbide advancements for drilling deep holes faster and better than ever

Deep hole drilling is defined by machining a hole that has a depth of at least 16 times the diameter (16xD). When parts call for a hole this long or even longer, special consideration must be given to the type of drill selected, and the machining strategy implemented while using the tool. The challenge is to machine a high quality hole that is within print specifications, and still produce parts at a rate fast enough, with tool life high enough, to make the job profitable. New advancements in solid carbide technology offer strong competition to traditional methods.

While gundrilling has proven to be an effective process for creating these deep holes, it is also an extremely slow process compared to drilling using solid carbide drills. Thanks to advances in cutting technology, these types of drills are now capable of machining depths ranging to 70 times the diameter, which was previously only considered possible with gundrilling.

A gundrill’s advancement per revolution and cutting speed yield a typical feed rate of 4 to 6 ipm (102 to 152 mm/min), while a solid carbide drill can run at higher advancement per revolution and higher cutting speeds due to the material’s inherent strength and the geometry of the drill’s point and body. Feed rates of 35 ipm and higher are not uncommon with solid carbide deep hole drills. Increased feed rates result in faster production times and increased part production by each machine, thereby lowering the cost of manufacturing.

Here are some advancements in technology and machining strategies that can improve deep hole drilling.
• Diameter tolerance. A pilot hole should be used when drilling holes at a depth equal to or greater than 16×D.

The pilot hole acts as a guide to help stabilize the longer drill at the beginning of the drilling process. Drill manufacturers offer special pilot drills specifically for creating this initial hole designed for this task with regards to the point angle and the diameter tolerance.

The diameter tolerance of a pilot drill is typically a unilateral (plus/plus) tolerance, for example, an ISO tolerance class of p7 that allows the user to select a pilot drill with the same nominal diameter as the deep hole drill (see image left). This tolerance ensures that the pilot hole is properly sized to support the drill and not cause interference.

• Point angle. When drilling into a pilot or pre-machined hole, the angle of the drill point should be smaller than that of the previous drill. This is to minimize the force load on the drill as the point penetratesthe material. If the point angles match exactly, this may cause a spike in the torque applied to the drill, whichcould break the drill or cause chatter.

It’s critical that all drill point angles and diameter tolerances be coordinated for deep hole drilling.Typically, pilot drills have a standard 145 to 150° point angle. Since hole depths ranging to 30xD can be prepared by only using a 2xD pilot hole, drills in the range of 16x to 30x the length-to-diameter ratio should have a point angle of 135 to 140°. This point angle configuration allows any drill to 30xD to work in sync with the standard pilot drill.

Solid carbide drills designed for lengths in excess of 30xD should use a 125 to 130° point angle. Drills in this length-to-diameter ratio range cannot be used with a 2xD pilot hole. Instead, the pilot hole should also be prepared with a second pilot hole, created with a drill in the 16xD to 20xD ratio.

Tools designed with varying point angles can stop the drill point from matching the angle of the previous drill point, which causes a large torque spike at initial engagement at the bottom of the pilot hole. If these factors are considered when solid carbide deep-hole drills are designed, the tool selection process is much clearer, as the end user only needs to be concerned with selecting tools based on the nominal drill size.

• Margin support. Once the drill point becomes fully engaged, the drill is supported on its margins (the bearing surface on the outside diameter of the drill body that runs along the edge of the flute). For deep hole drills, two margins per cutting edge is standard. However, due to the geometry of the clearance angles and the gash on the drill point, the second margin may not be close enough to the point, and therefore cannot engage until much later (approximately 1 to 2xD). This leaves the drill point with less than maximum support in this critical range, until the second margin can become engaged (see first image below).

A pilot drill with the correct point angle can improve a deep hole drill’s performance and life.To combat this issue, newer deep hole drills have moved the second margin from the trailing edge to the middle of the drill land. This moves the start of the second margin closer to the drill point and allows it to become fully engaged much earlier, quickly allowing full support to guide the drill point.

• Radial or perpendicular margins. A new concept in solid carbide drill design involves an innovative land design that orients the margins radially or perpendicular to the flute rather than parallel to the flute (see centre bottom image ). Configuring the margins in a radial orientation around the drill point eliminates the need to wait for the second margin to engage. Solid carbide material provides support directly behind the cutting edge and continues for the full width of the land, which immediately provides maximum support and guidance to help produce the straightest possible hole.

• Strong cutting edges. Additional solid carbide material located behind the cutting edge makes a stronger tool, because that added material is positioned to directly oppose the largest cutting forces. A stronger cutting edge design offers two benefits: 1) the machinist can take advantage of an overall increase in production rates by using higher advancement per revolution, and 2) longer tool life can be expected due to the additional material, which means greater production runs, more machine uptime and decreased cost to the manufacturer.

Pushing the limits
Many different parts call for holes with exceptional length to diameter ratios. Creating these holes requires special drills that have extraordinary length-to-diameter ratios. With advancements in materials, tool designs and machining strategies, these drills now can perform at lengths never before thought possible. By making the drills from solid carbide, the tools can be pushed with higher cutting speeds and feed rates, and generate faster production rates, yielding easier part production for the machinist and more profit for the shop owner. SMT

 

Luck Pollock is product manager, round tools for Walter USA LLC.

 

Share This Post


Recent Articles



Wordpress Social Share Plugin powered by Ultimatelysocial
error

Enjoy this post? Share with your network