Fronius ArcTigClick image to enlarge

Fronius has developed a modified TIG welding process that addresses speed requirements as well as seam quality.

Called ArcTig, the process utilizes a special welding torch that allows the TIG arc to be focused in a targeted manner and significantly increases its energy density while providing exceptional cooling. Users can weld up to ten millimeter thick, high-alloy sheets and pipes without extensive seam preparation, to an exceptionally high quality standard and much quicker.

The ArcTig welding process from Fronius is based on the principle of tungsten inert gas welding, or TIG welding for short. In this process, an arc burns between a non-melting tungsten electrode and the metallic workpiece in an oxygen-free, reactionless gas atmosphere. The current flow heats the electrode, resulting in an electron flow. This reduces the combined resistance, producing a soft, wide arc. The inert protective gas shield means there are no chemical reactions with the liquid weld pool. This enables users to produce a perfect weld-seam appearance without tempering colors and spatter as well as the best weave pattern. TIG welding is suited to a variety of different materials and applications, including tricky materials like titanium.

The ArcTig welding process is designed for applications in container and pipeline construction, in the manufacture of turbines and the construction of special machines, cranes and tanks. The key innovation here is the optimized welding torch with an electrode clamping system, which enables the electrode to be cooled right to the tip. This increases the combined resistance and creates a high arc voltage. Electron emission now takes place over a small area but at an extremely high density. This makes the arc narrower and more targeted, allowing the user to achieve exceptional weld seam quality. Another advantage of the cooling is that it prevents overheating of the electrode during welding, providing increased arc stability and ensuring a longer service life and improved ignition. Users can upgrade all TIG power sources from Fronius above an output of 220 amperes to the ArcTig process with ease. The only equipment required is the new welding torch and an additional heat exchanger to provide the cooling capacity and the required temperature stability. ArcTig is also available as a complete system.

Shorter processing times and lower filler metal costs

The focused and high-pressure arc means the ArcTig can be used to weld components in one layer to a material thickness of up to ten millimeters. In conventional TIG welding, several layers are often needed. Additionally, it is frequently the case that users no longer need to do time-consuming preparation work on parts. As there is no gap during seam preparation, no weld pool support is required for the ArcTig process. This cuts down on rework to a large extent, since the weld seam is raised to a minimal degree and there is very little distortion due to the reduced heat input. This enables users to accelerate processing times considerably, while the welding process also permits higher welding speeds. What's more, material costs are lowered as the weld seam volume is reduced.

The ArcTig process also impresses in terms of operation: because it is very similar to TIG welding, users do not have to adjust to a new process and can weld immediately without carrying out any time-consuming teaching-in. This minimizes the need for training and prevents incorrect operation by the welder, as just a few parameters need to be set. Users can make use of standard TIG electrodes that are quick to change and can easily be re-ground as necessary. The new electrode clamping system clamps the electrode over a large area. To make the weld seam more accessible and enable the arc to be manipulated better, the free end of the electrode can be adjusted as desired depending on the requirements.

Similar Articles

Multi-process welding system

ESAB's new Rebel EMP 215ic is a 120V-230V CC/VC welding system the company says offers true multi-process arc performance.

Aluminum MIG push-pull welding systems

Lincoln Electric has introduced two new aluminum MIG push-pull welding system packages, the Power MIG 350MP and One-Pak.

Higher productivity welding in heavy fab applications

Flex Feed 84 is Lincoln Electric's latest additon to its line of wire feeders. The company says it delivers consistent feeding over long conduit runs iwth large diameter wires up to 2.4 mm (3/32 in.).

Robotic nozzle cleaning station cuts costs

Tregaskiss has introduced the Tough Gun TT3E Reamer, a robotic nozzle cleaning station with digital Ethernet communications to better integrate into companies' digital controls infrastructure.

Chromium-free hardfacing wire

Eutectic has introduced what it says is the hardest wire with no hazardous chromium by-products, BoroTec 600 Cr-Free.

Stay In Touch

twitter facebook linkedIn